How To Use A Cording Foot

A serger isn't just for finishing raw edges. Learn about useful serger presser anxiety that accept your sewing to the next level and help yous accept full advantage of everything your serger can practice. Annotation: The featured serger feet imagery are for Janome sergers.

Blind Hem Foo t

Employ a blind hem foot to create an invisible hem on a garment or home-décor project. Fold the fabric toward the wrong side to the desired hem width. Fold the fabric with correct sides together, exposing a scant 1?2" of the raw edge. Position the textile incorrect side upwardly beneath the pes. Select a two- or 3-thread narrow hem sew together on the car. Slowly lower the needle into the fabric to check the needle placement. The left needle should barely graze the hem, catching one or two fibers. The pes-edge guide should be flush with the fabric fold. With the knife bract up, serge the hem, making certain to only cutting off the fabric raw edge, catching the fold inside the stitching. Printing open the seam.

Gathering Human foot

The gathering foot finishes a seam and attaches a ruffle in i step. For best results, use lightweight fabric, such as cotton. Heavyweight fabric, such as denim, produces fewer ruffles. Cut the fabric to be gathered (lower textile) longer than the upper material (ii:ane ratio). Select a 4-thread overlock stitch on the machine. Raise the presser foot. Position the lower fabric under the foot just below the needle. Position the upper fabric between the guide over the lower material. Lower the presser human foot. Slowly plough the manus bike toward you to stitch the first three or four stitches to aid the machine catch the fabric without jamming; stitch. While stitching, hold one fabric in each hand to evenly guide it through the machine. Don't apply pressure to the lower material, as this prevents gathers from forming. Hold the upper fabric taut. Adapt the assemble size by irresolute the stitch length between 2mm and 5mm. Remove the textile from the machine; press open the seam.

Beading Foot

Use the beading human foot to attach a strand of beads directly to fabric to create a decorative hemline or an easy embellishment. The run up selection varies according to machine brand. Check with the car manual and foot instructions to select the proper sew type. Pull the cord of chaplet along the pes guide toward the back. Extend the bead string at least 1cm past the fabric edge to ensure the auto catches both the beads and fabric. The stitch length should be the size of the bead diameter. For example, if using 3mm beads, select a 3mm run up length. Some machines recommend folding the fabric with wrong sides together and aligning the beads along the folded edge earlier stitching. Position the folded border forth the foot border; stitch. With this method, the raw edge won't exist finished. Or go along the serger pocketknife in the up position while stitching a 3-thread rolled hem to ensure that the edge is finished simultaneously every bit the beads are stitched.

Piping & Cording Pes

Insert a professional-looking piped border into a garment or accessory quickly and easily using the pipe/cording foot. Note that for some makes and models, such as those shown hither, these are separate anxiety. Select a 3mm-long 3-thread overlock run up. Sandwich the pipage tape between two fabric pieces with right sides together, aligning the raw edges. Position the textile sandwich nether the presser human foot, adjustment the piping inside the pes groove. Stitch, and then turn the fabric to the right side; press. Or sew together piping to the center of material by disengaging the knife and selecting a chain stitch.

Elastic Foot

Easily stitch elastic to a fabric edge using an rubberband foot. Adjust the pressure on the elastic every bit you stitch to create the desired amount of ruffles. The foot too slightly stretches the elastic as you stitch, preventing pulling and tugging on the needles. Select a 3- or 4-thread overlock stitch on the machine. Conform the pes tension past turning the punch at the foot toe. Tightening the screw adds force per unit area, causing the elastic to stretch more, increasing the gathering. Insert the elastic into the guide on the pes and so that the elastic correct-side edge aligns with the guide. Turn the guide knob so it abuts the elastic left-side edge. Carefully turn the paw wheel toward you lot to accept a few stitches. Once the elastic and material are feeding smoothly, stitch at medium speed. Janome of America sponsors this series and provided serger feet and the AT 2000D serger.

Originally posted on Dec 1, 2018; updated on April 25, 2022.